A'PEX SUPER AFC ? Manual de instrucciones

1 A’PEX Chasing Our Dreams - A complete line of customized car and automotive parts developed with state of the art technology and new ideas. Our co

10

11 第２章 Chapter 2 Procedure before Using This Product _____ 12 Perform initial setup ___________________ 13 Setting the sensor type and sensor numbe

12 Procedure before Using This Product Install this product The details of the installation procedure are described in the separate “Vehicle Specifi

13 ● Do not start the engine before starting the initial setup If the engine is started without initial setup, the engine may be damaged. WARNING ！

14

15 Chapter 3 Outline of Operating Method Outline of Functions and Operating Method____16 What to be performed in the monitor mode_____18 What to be

16 Outline of Functions and Operating Method Main menu The SAFCⅡ consists mainly of 3 menus; Monitor mode The data obtained from the sensor is di

17 [Channel 1 to Channel 4] display items 1. Afl ...Airflow (Hot wire/Flap) usage ratio 2. Prs ... Intake pr

18 Functions and Operations in the monitor mode Main menu 【Monitor】 [Contents of items] 1. Afl ...Airflow (Hot wire/Flap) usage ratio

19 Functions and Operations in the setting mode Main menu 【Setting】 Functions and Operations in the etc. mode Main menu 【etc.】 1. Sensor Type...

2 Contents Chapter 1 Introduction Safety Precautions _____________________________________________________________________4 Features of this Product_

20

21 One of items 1 to 4 is selected and displayed _________________________22 A plot display is made by using the RPM for the axis _______________

22 ●Graphic display 【Function】 Pause and replay ２. Select [1 to 4 Channel] in the monitor menu １. Select [Monitor] in the main menu Main menu

23 ※When the upper part of the center switch is pressed, the operation is the same as when the rotary switch is turned clockwise. When the lower pa

24 ●Function at numeric display and analog display Reset The item is displayed as a reversing display ４. The selected item is displayed in the it

25 ●Function at graphic display ●Regarding the 3 items Afl, Prs, and Kar, the contents that can be displayed depend on the intake air v

26 ●Function in the digital/analog display ※In the digital/analog display, a 4 channel display is made regardless of the selected channel. The dis

27 Main menu ２. Select [Rev. –[Y]] in the monitor menu １. Select [Monitor] in the main menu ３. Select the data to be displayed in the item sel

28

29 Setting Mode Chapter 5 Air correction factor setting (Throttle opening, large) ___________________________________ 30 Air correction factor sett

3 Chapter 1 Introduction Safety Precautions____________________________________4 Features of this Product ____________________________6 Names and F

30 Select Select 【Setting Menu】→【Hi-Thrtl】・【Lo-Thrtl】 Air correction factor setting (Throttle opening, large / small) or Setting menu Correction f

31 Correction factor increase/decrease RPM selection Ordinary display image diagram Reduced display Actual ordinary display 【Hi-Thrtl】 ※When the

32 Select Select Select ２. Select [TH-Point] in the setting menu １. Select [Setting] in the main menu or Main menu Setting menu or (1) Sele

33 Correction factor change due to throttle opening setting. 0.25 0.75 Throttle opening +3% +2% -1% 0 20% 40% 60% Correction value Air correction f

34 Increase/decrease Select Select Select Engine revolution speed selection or Pr 【Setting Menu】→【Ne-Point】 Air correction engine RPM setting ２.

35 Engine revolution speed (rpm) 1000 1600 2200 2800 3400 4000 4600 5200 5800 6400 7000 7600 0 -4 -2 0 1 2 2 1 0 -1 -2 -3 -3 1

36 Select Select Select In the case of a turbo vehicle equipped with a hot wire type airflow sensor, the engine may be stalled by blow-back when th

37 1. Ne01 / Ne02 RPM check Turn on the ignition switch, and check the Ne01/Ne02 RPM at air correction point setting [Ne-Point]. The initial value i

38 Correct Select Select Select (1) Select a correction revolution point Press the upper or lower part of the center switch or turn the rota

39 Correct Setting Knk Set １. Correct RPM 1 Hold the engine RPM at a fixed value between 1300 rpm and 1700 rpm in the no-load status (neutral).

4 ●Do not use this product for any application other than applicable vehicles or applicable goods . We shall disclaim the responsibility for operati

40 Changeover Select Select Select ２. Select [Data File] in the setting menu １. Select [Setting] in the main menu or Main menu Setting menu

41 (1) Select a data file Press the upper or lower part of the center switch and turn the rotary switch counterclockwise or clockwis

42

43 Etceteras (etc.) Mode Chapter 6 Sensor type and sensor number setting__44 Number-of-cylinders and throttle sensor type setting__________________

44 Select Select Select 【etc.】→【Sensor Type】 Sensor type and sensor number setting The sensor type and the sensor number (sensor characteristic) a

45 Select ●When the sensor type is set to Hot-Wire or Pressure Depending on the car specifications, the In setting and the Out setting must be chan

46 At In selection At out selection At out selection At In selection Select ５. Set the sensor output calculation method ※Pressing the upper part

47 SUPERAIRFLOW CONVERTEROut 1 ※Because of a single engine control unit input SUPERAIRFLOW CONVERTERMeasured air volume 10 Output air volume 10 Set

48 SUPERAIRFLOW CONVERTERSUPERAIRFLOW CONVERTEROut 1/2 In 1 Out Add Setting the sensor output calculation method (3) ●General vehicles using 2 airflow

49 Select ●When the sensor type is Flap or Karman ※For the sensor numbers, refer to the Wiring diagram by model on the separate sheet. 1. For Flap

5 WARNING ！ ●Regarding the installation of this product, be sure that it is installed by an experienced professional Installing the product requires

50 Select Select Select Select Set the number of cylinders and the throttle type according the vehicle. This item is indispensable for initial se

51 Select ●When No throttle signal (＊＊) is set, correction is not performed by throttle opening, so you can set only the Hi mode [Hi-Thrtl] in the a

52 Select Select End the check Select [Pr] in the popup menu after pressing the center pushbutton or press the left part of the center switch, a

53 Select Select (1) Select an item Press the upper or lower part of the center switch and turn the rotary switch counterclockwise or clockwi

54 Select Select When the unit of pressure display is set to Pascal (kPa) in the display scale setting on the previous page, the unit of pressure w

55 (1) Select an item Press the upper or lower part of the center switch and turn the rotary switch counterclockwise or clockwise to

56 Select 【etc.】→【Pass Lock】 Password setting and change When a password is optionally set, this can prevent setup data or setting data from being c

57 (1) Input the password Turn the rotary switch counterclockwise or clockwise and input a password. For the password, select characters from 0 to 9

58 Select Select Select (1) Select an item Press the left or right part of the center switch to select an item to set a numeric value. The selecte

59 Select Select 【etc.】→【Program Ver.】 Program version check ２. Select [Program Ver] in the etc. menu １. Select [etc.] in the main menu Main m

6 ●This product cannot be used for any application other than the vehicles mentioned in the separate Vehicle Specific Application Charts. ●Note tha

60 Select Select Select 【etc.】→【Initialize】 All data initialization Initialize all data to return it to the data status provided at delivery from

61 ●Memo

62 ●Check if the battery is connected. ●Check if the vehicle ECU harness is securely connected to the signal harness. ●Check if the signal harness

63 The display is dark or bright ・Make a VFD brightness adjustment. (P58) The engine is out of order ●An engine stall occurs. ・Check if the harness

64 Where to contact http://www.apexi.co.jp Authorized Agencies TAIWAN AAI MOTORSPORTS CO.,LTD B1, NO. 162, Jian

7 Storing two patterns of setting data in the memory Two patterns of setting data including air correction factor, throttle opening, air correction

8 Names and Functions of Parts Parts list Before installing this product, be sure to check the parts list to confirm that there are not any fore

9 Example) ●Popup menu When you press the center pushbutton, the popup menu shown at right appears. The selected portion will appear as a reverse